Adtec-digital RD-70 (version 1.02.04) Manual Manuel d'utilisateur

RD-7010-bit / Multi-CODEC 1080PReceiver / DecoderIncludes demodulator versions - ADV, LB and PRMUSER GUIDE02.10.15- v1.02.03

Transport LED IndicatorsIndicator FunctionDecode Off - Decoder is idle.On - Decoder is active.ASI / IP /RF Off - No services detected on the input.On

BISS Off - Decryption configuration is turned OFFOn - Decryption configuration is set to BISS1 or BISSE Link Off - Network communication link not de

Front Panel Menu StructureServices MenuItem Function OptionsList of Services Allows selection of a service from a list of services per input.ALL ASI

RF Rx Menu (ADV Advanced / PRM Premium)Item Function OptionsSelect Tuner*Selects RF1 or RF2 as the RF acquisition source RF1RF2Local Oscillator The Lo

capacity that is realized while using the method. If Auto-CCM is selected, the receiver will detect and configure the Modulation Mode, Pilot, and Fram

the RF tuner will sweep through to acquire the carrier. e.g. If the desired carrier is at 1.080GHz and the Acquisition Range is set to 5MHz, the RF tu

configurations.LNB Polarity This control is primarily used in “Universal” LNB applications. The LNB Polarity control allows for LNB polarization selec

If the Downlink frequency is greater than the Local Oscillator frequency, then spectrum inversion does not occur.Local Oscillator The Local Oscillator

LNB Tone This control is used only for Universal LNB applications. A universal LNB can route the high or low band from either polarity to the IRD. The

IP Rx MenuItem Function OptionsMulticast RX IP Multicast IPA sets the multicast receive Group IP address. IP Multicast receiving is supported from com

ContentsContentsTrademarks & CopyrightsElectrical Device Compliance NoticesSafety Warnings and CautionsComplia

value is 300 milliseconds. If the timeout value is set too low, the multicast receive may timeout during normal reception if the packet transmission i

selected, the current device name will be used.3G Mapping Level SDISDI 3G Level controls the mapping of the 3G-SDI signal when decoding 1080P50, 1080P

and REMOTE is used in standard genlock operation.signalREMOTE - Enable genlock, Decode source is NOT synchronous to SYNC IN signalHorizontal AdjustHor

Audio MenuItem Function OptionsAudio AssignOrderThe RD automatically assigns audio PID's to audio engines upon stream acquisition. This setting d

DolbyD ModeConfigures the audio engine toPass-through ( COMPRESSED )or decode ( 2/0 STEREO ) if a Dolby Digital AC3 PID is detected for the selected A

SDI pairAUDIO3, Route Audio 3 to the selected SDI pairAUDIO4, Route Audio 4 to the selected SDI pairAUDIO5, Route Audio 5 to the selected SDI pairAUDI

VBI MenuItem Function OptionsTime CodeSDI Line Number Configures the SDI ANC line output of VITC/LTC ( SDI Output Port 1 and 2 )0 - Disabled7 - 22SDI

TeletextCVBS Line NumberEnables/Disables the CVBS/SD-SDI port line number for waveform Teletext.0 - Disabled22 - Output teletext if presentSDI Line Nu

CAS MenuItem Function OptionsMode Configures the current decryption setting. OFFBISS_1BISS_E_USER_ID_ONEBISS_E_USER_ID_TWOClear Session Word The sessi

System MenuLoginUnits ship with the front panel logged in by default. If you become logged out and are prompted for a password, use the following key

Compatible browsersEthernet AccessZero Configuration AccessLoginFirmware Upgrade via Web User InterfaceDe

Item Function OptionsNetwork MenuEthernet IP Address This is the address of your deviceon your network specific to the Ethernet Port.user-defined usi

access to the Stealth IP Address.Time MenuTime Defines system time user-defined using the numeric keypadTimezone Defines the time zone the unit operat

Com2Item Function OptionsCom2 Settings RS-232 terminal monitor for communicating with the internal host motherboard for diagnostics. 115200 8 1 NONE57

Back PanelConnector DescriptionProcessorPower 1 & 2 Redundant AC Power, Standard 3 pin computer power plug(Auto range 70-240 VAC Input)GigE UDP o

this time.x3 ASI OUT x3 75 Ohm BNC ASI output per EN5000839Sync In Standard analog video sync separation for NTSC, PAL, 480I/P, 576I/P, 720P, and 1080

COM1/COM2 to DB9 Serial AdapterThe COM1 and COM2 port is an industry standard RS-232 DTE device on RJ45/RJ48. Units ship with RJ45 to DB9 adapters th

3 D2 reserved for future functionality4 D1 reserved for future functionality5 D0 reserved for future functionality6 NC No Connect7 5VDC +5V DC8 GND gr

Chapter 2 - Getting ConnectedIntroduction to the Control ApplicationA web-based control software application comes pre-installed on the RD-

reach the device’s web application by pointing your browser to the IP Address of the device.Ex.http://192.168.10.48/. LoginOnce you reach the default

Trademarks & CopyrightsCopyright: (c) 2011-13 Adtec Digital. All rights reserved. This document may not, in whole or in part, be copied, pho

Click on the Install button associated with the new file. Wait for it to completely extract and become available in the Installed Versions List. Once

The time required to update firmware varies on hardware model and should be accounted for during the maintenance windows.Estimated Time required to up

!!NOTE!! It is only recommended to update during a planned maintenance window. If a firmware upgrade fails for any reason, it is OK. Just try the u

3 When prompted for a username, enter adtec. 4 When prompted for a password, enter none.Once you see "User 'adtec' connected", the

In Field Feature UpgradesUnit features can be upgraded in the field via the web user interface. Keys can either be temporary (feature will stop worki

Temporary Key InstructionsIf a temporary key is provided, it will be in the form of an email attachment or file. Temporary keys are not entered throug

Feature Key DescriptionsBase Unit KeysPdRD70 - This is the product key to determine product typeMP2-BASE-D - Adds Mpeg2 4:2:0 and 4:2:2 decode capabil

Chapter 3 - Operational InformationDVB-S / DVB-S2 AUTO Modes (ADV and PRM option)The RD-70 Advanced and Premium demodulators support automa

● Click the Apply button to save information to the currently running configuration● Click the ‘Create RF Profile’ button next to the respective tuner

UDP / RTP / FEC / TCP IP RxThe RD-70 supports a number of IP based protocols for the reception of transport streams via private and public networks.

Electrical Device Compliance NoticesSafety Warnings and CautionsFor your safety and the proper operation of the device:● This unit must

When receiving FEC streams behind firewalls, please bear in mind that two additional ports (N+2 and N+4 ) must be allowed through for proper error rec

where 0 <= xxx <= 255. If you are new to multicast and attempting a first time connection,226.0.1.1 is a common address to start with. Please

‘Select first found’ is also available via the Front Panel -> Services Menu -> Select First configuration. Use the left/right arrows to select

Note: Encoder must support alignment for aligned audio feature.The RD-70 automatically configures the audio engines upon acquisition of a program when

The RD-70 AFD implementation preserves the native AFD code from the video elementary stream and is inserted into the SDI ancillary data output. The S

Genlock SystemThe RD-70 can synchronize its SDI and CVBS outputs to an external sync signal using the SYNC IN input and the Genlock control system. Th

TS Out DecryptTSO or Transport Stream Out Decrypt is a newer feature of the RD product line that determines how BISS encrypted transport streams are p

Chapter 4 - AppendixAppendix A - GNU General Public LicenseVersion 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc.59 Temple

that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and tellin

television reception, which can be determined by turning the equipment off and on, the useris encouraged to try to correct the interference by one or

"any later version", you have the option of following the terms and conditions either of that version or of any later version published by t

Appendix B - Technical SpecificationsBase Model (RD70-XX)InputsDVB-ASIUse: Input available for Decode or Pass to ASI outputs.Standard: Asynchronous Se

SDI Ancillary data and OSD overlay have unique configuration for each SDI bankConnector: Three BNC (75 Ohm), One SFPnote*: 3G-SDI Outputs have selecta

GPIO PortUse: not used as this timeConnector: DB9 MaleVideo and AudioVideo DecodeMPEG-2 SD (ISO/IEC 13818-2) Decode:Format: 480i59.94, 576i50Profiles:

Certification / ComplianceRoHS CompliantAdvanced Demodulator (ADV option)note: Software keys are required to unlock full hardware support.Modulation S

L-Band Demodulator (LB option)note: Software keys are required to unlock full hardware support.RF Inputs: Dual RF inputs capable of simultaneous lockE

Premium Demodulator (PRM option)note: Software keys are required to unlock full hardware support.Modulation Scheme support: QPSK / 8PSK / 16APSK / 32A

Appendix C - Adtec Digital Support & ServiceTechnical Support and Customer Service includes troubleshooting product/system functional operations c

information regarding the problem. Please include your facility name (or call letters), your name, title, email address, telephone number, hours of wo

Chapter 1 - Product IntroductionCovered EquipmentRD-70: 1080P59.94 MPEG 4 10 Bit / MPEG 2 Capable IRD. Transport Stream inputs standard on

Front Panel LCD1) Feedback State: There are several quick view menu screens available when in regular feedback state. You can view any of these quick

2) Disabled Product State: When the product is in a disabled state, the LCD will relay the following information. This state is generally only used wh